espaceur
Log inLog in

Password
OK
Register - Forgotten password
filet
loupe Text OK loupe Reference OK loupe Families OK loupe Several points OK
My basket My basket
Heater cartridge
Télécharger la brochure détaillée

HEATING RESISTANCES REGULATION

Trier par
Heating cartridge  cold conformed
Télécharger le PDF
>> détail du produit
Heating cartridge cold conformed
Heating cartridge cold conformed
Sheath stainless, sections 3 X 3 mm, 2,2 X 4,2 mm or 5 X 7 mm
Inactive zone = 90
Output wire (2 drivers + ground) isolated silk from glass, protected under:
- insulating sleeve silk of glass silicon (for sections 3 X 3 mm and 2,2 X 4,2 mm)
- braid steel (for section 5 X 7 mm)
Supply voltage 230 V

Options:
- Return to the earth according to model
- Other sections on request: Ø 3 mm, Ø 4 mm, 6 X 6 mm, etc…, us to consult
- realizable Forming and plane bending following
- Models with thermocouple incorporated on request
Heating cartridge - High temperature
Télécharger le PDF
>> détail du produit
Heating cartridge - High temperature
Protection Sheath stainless
Welding TIG
Magnesium compacted oxide core and insulation
Supply voltage 230 V
Electric connection by covered drivers nickel silk of glass, standard length 250 mm
Resistive wire NiCr 80/20

Applications:
- Industry plastic, bakelite, epoxy, polyester and rubber
- Hot Moulds - Refrigerating of absorption
- Heating of metal masses
- Marking Machines - Industry of the bolster

Options:
- Another dimensional range (length: sheath + output flexible, Ø)
- Another electric range (voltage, power)
- Another type of assembly (output bent, cable protected by flexible device stainless,…)
- Another electric End fitting
- Return by the earth
- Differentiated Heating (variable specific heating over the heating length)
- Thimble during the heating of a fluid

Precautions for use:
- Use a product lubricating which will facilitate the assembly and the disassembling of the heating cartridges within their boring while ensuring a good thermal conductibility. See heat-conducting grease silicone (ref. GSTC)
- So not burning the junctions or roasting resistance, take care to leave the electric cable out of boring and introducing the whole of the sheath inside this last
- Protect the electric junctions against moisture, the metal particles which could generate leakage currents.
- Avoid the vibrations and ensure a good mechanical stability it temperature sensor must be placed at 10 mm maximum of the cartridge. The minimum difference between the cartridges is equal to two diameters

Accessory:
Heat-conducting grease silicone (ref. GSTC)
- Is used to conduct the heat by filling space between various materials
- Insulating electric - Does not harden, resists water, not corrosive
- Temperature of use: -60 to + 205 °C - Conservation: > 1 year at temperature lower than 50 °C
- Solvent: trichloréthane
- For higher temperatures, to consult us!
Heating cartridge - Low temperature
Télécharger le PDF
>> détail du produit
Heating cartridge - Low temperature
Protection Sheath stainless
Welding TIG
Magnesium compacted oxide core and insulation
Supply voltage 230 V
Electric connection by covered drivers nickel silk of glass, standard length 250 mm
Resistive wire NiCr 80/20

Applications:
- Industry plastic, bakelite, epoxy, polyester and rubber
- Hot Moulds - Refrigerating of absorption
- Heating of metal masses
- Marking Machines - Industry of the bolster

Options:
- Another dimensional range (length: sheath + output flexible, Ø)
- Another electric range (voltage, power)
- Another type of assembly (output bent, cable protected by flexible device stainless,…)
- Another electric End fitting
- Return by the earth
- Differentiated Heating (variable specific heating over the heating length)
- Thimble during the heating of a fluid

Precautions for use:
- Use a product lubricating which will facilitate the assembly and the disassembling of the heating cartridges within their boring while ensuring a good thermal conductibility. See heat-conducting grease silicone (ref. GSTC)
- So not burning the junctions or roasting resistance, take care to leave the electric cable out of boring and introducing the whole of the sheath inside this last
- Protect the electric junctions against moisture, the metal particles which could generate leakage currents.
- Avoid the vibrations and ensure a good mechanical stability it temperature sensor must be placed at 10 mm maximum of the cartridge. The minimum difference between the cartridges is equal to two diameters

Accessory:
Heat-conducting grease silicone (ref. GSTC)
- Is used to conduct the heat by filling space between various materials
- Insulating electric - Does not harden, resists water, not corrosive
- Temperature of use: -60 to + 205 °C - Conservation: > 1 year at temperature lower than 50 °C
- Solvent: trichloréthane
- For higher temperatures, to consult us!
PLATINUM RTD (PT100) PROBES | THERMOCOUPLE TEMPERATURE PROBES | DATALOGGERS WEATHER STATION | HEATING RESISTANCES REGULATION | WEATHER STATION AND MICROCLIMATE STATION | MOBILE MEASURING | MEASURING TRANDUCERS AND GALVANIC INSULATORS | CONTROLLERS AND INDICATORS AND THERMOSTATS | ACQUISITION AND MONITORING | SENSOR TRANSMITTER |

Homepage - Who are we ? - Request for documentation - Downloads - Contact - Newsletter - My basket
Seacrh Families - Advanced search
Equipement et matériel pour les audits énergétiques

PROSENSOR 15, rue de Montvaux 57865 Amanvillers - FRANCE
Phone  (33) 03 87 53 53 53 - Fax (33) 03 87 53 53 55
Website: www.prosensor.com - Email: info@prosensor.com

Realization: netcomposant
W3C GANDI SSL